Encyclopedia > IGC

  Article Content

Inertial guidance system

Redirected from IGC

An inertial guidance system sometimes also called an inertial navigation system, measures the position and attitude of a vehicle by measuring the accelerations applied to the system. It is widely used because it refers to no real-world item beyond itself. It's therefore immune to jamming and deception.

IGSs have angular accelerometers, and linear accelerometers.

Angular accelerometers measure how the vehicle is twisting in space. Generally, there's at least one sensor for each of the three axes: pitch (nose up and down), yaw (nose left and right) and roll (clockwise or counterclockwise from the cockpit).

Linear accelerometers measure how the vehicle moves. Since it can move in three axes (up & down, left & right, forward & back), it has a linear accelerometer for each axis.

A computer comtinually calculates the vehicle's current position. First, for each of six axes, it adds the amount of acceleration over the time to figure the current velocity of each of the six axes. Then it adds the distance moved in each of the six axes to figure the current position.

Inertial guidance is impossible without digital computers. The desire to use inertial guidance in the minuteman missile and Apollo program drove early attempts to miniaturize computers.

Inertial guidance systems are now usually combined with satellite navigation systems through a digital filtering system. The inertial system provides short term data, while the satellite system corrects accumulated errors of the inertial system.

Table of contents

Schemes

Gyrostabilized platforms

Some systems place the linear accelerometers on a gimballed gyrostabilized platform. The gimbals are a set of three rings, each with a pair of bearings at right angles. They let the platform twist in any rotational axis. There two gyroscopes (usually) on the platform.

Why do the gyros hold the platform still? Gyroscopes try to twist at right angles to the angle at which they are twisted (an effect called precession). When gyroscopes are mounted at right angles and spin at the same speed, their precessions cancel, and the platform they're on will resist twisting.

This system allowed a vehicle's roll, pitch and yaw angles to be measured directly at the bearings of the gimbals. Relatively simple electronic circuits could add up the linear accelerations, because the directions of the linear accelerometers do not change.

The big disadvantage of this scheme is that it has a lot of precision mechanical parts that are expensive. It also has moving parts that can wear out or jam.

Rate Gyro Systems

Lightweight digital computers permit the system to eliminate the gimbals. This reduces the cost and increases the reliability by eliminating some of the moving parts. Angular accelerometers called "rate gyros" measure how the angular velocity of the vehicle changes. The trigonometry involved is too complex to be accurately performed except by digital electronics.

Laser Gyros

Laser gyros were supposed to eliminate the bearings in the gyroscopes, and thus the last bastion of precision machining and moving parts.

A laser gyro moves laser light in two directions around a circular path. As the vehicle twists, the light has a doppler effect. The different frequencies of light are mixed, and the difference frequency (the beat frequency) is a radio wave whose frequency is supposed to be proportional to the speed of rotation.

In practice, the electromagnetic peaks and valleys of the light lock together. The result is that there's no difference of frequencies, and therefore no measurement.

To unlock the counter-rotating light beams, laser gyros either have independent light paths for the two direction (usually in fiber optic gyros), or the laser gyro is mounted on a sort of audio speaker that rapidly shakes the gyro back and forth to decouple the light waves.

Alas, the shaker is the most accurate, because both light beams use exactly the same path. Thus laser gyros retain moving parts, but they don't move as much.

Brandy Snifter Gyros

If a wave is induced in a globular brandy snifter, and then the snifter is tilted, the waves continue in the same plane of movement. They don't tilt with the snifter. This trick is used to measure angles. Instead of brandy snifters, the system uses hollow globes machined from piezoelectric matierals such as quartz. The electrodes to start and sense the waves are evaporated directly onto the quartz.

This system almost has no moving parts, and it's very accurate. It's still expensive, though, because precision ground and polished hollow quartz spheres just aren't cheap.

Pendular Accelerometers

The basic accelerometer is just a mass with a ruler attached. The ruler may be an exotic electromagnetic sensor, but it still senses distance. When the vehicle accelerates, the mass moves, and ruler measures the movement. The bad thing about this scheme is that it needs calibrated springs, and springs are nearly impossible to make consistent.

A trickier system is to measure the force needed to keep the mass from moving. In this scheme, there's still a ruler, but whenever the mass moves, an electric coil pulls on the mass, cancelling the motion. The stronger the pull, the more acceleration there is. The bad thing about this is that very high accelerations, say from explosions, impacts or gunfire, can exceed the capacity of the electronics to cancel. The sensor then loses track of where the vehicle is.

Both sorts of accelerometers have been manufactured as integrated micromachinery on silicon chips.

Accelerometer-only Systems

Some systems use four pendular accelerometers to measure all the possible movements and rotations. Usually, these are mounted with the weights in the corners of a tetrahedron. Thus, these are called "tetrahedral inertial platforms", or TIPs.

When the vehicle rolls, the masses on opposite sides will be accelerated in opposite directions. When the vehicle has linear acceleration, the masses are accelerated in the same direction. The computer keeps track.

TIPs are cheap, lightweight and small, expecially when they use imicromachined integrated accelerometers. However currently (2002) they are not very accurate. When they're used, they're used in small missiles.



All Wikipedia text is available under the terms of the GNU Free Documentation License

 
  Search Encyclopedia

Search over one million articles, find something about almost anything!
 
 
  
  Featured Article
Flapper

... War I forced women to break even more gender barriers by entering the workforce to replace the large numbers of men fighting overseas. At war's end, women were expected to ...

 
 
 
This page was created in 35.8 ms